jib connections :: Catamaran Sailboats at TheBeachcats.com

Welcome anonymous guest

Please Support
TheBeachcats.com

jib connections

Go to page 1 - 2 [+1]:

iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 19, 2012 - 02:48 PM

Does anyboby have a good way to connect jib blocks to jib? I was tring to do it with a piece of line. I dont know the knot I should use for easy connect and disconnect. a picture would be great. thanks in advance for your ideas.
yurdle

Rank: Mate

Registered: Aug 22, 2007

Last visit: Jan 07, 2015

Posts: 742
Posted: Oct 19, 2012 - 03:54 PM

I don't have a picture on hand (can get one if necessary) but if you luggage tag a line, at its midway point, to a snap shackle, you can then snap the shackle on and off of the clew. Tie your blocks for 2:1 on to each end of the line. This is a pretty common setup for beach cats.

--
Rob
OKC
Pile of Nacra parts..
--
pknapp66

Rank: Mate

Registered: May 09, 2009

Last visit: May 15, 2023

Posts: 684
Posted: Oct 19, 2012 - 04:09 PM

the shackle at the top of the diagram connects to the jib clew (hole at the bottom rear of the jib)

--
Pete Knapp
Schodack landing,NY
Goodall Viper,AHPC Viper,Nacra I20
--
dhennessy

Rank: Lubber

Registered: Apr 06, 2011

Last visit: May 19, 2017

Posts: 35
Posted: Oct 19, 2012 - 05:06 PM

Tie a section of vectran or spectra at the middle of the line using a overhand knot to the clew. Tie the jib blocks to each end (separately) of the line using a bowline knot. The length of line from the clew to your sheeting block should be just short of the minimum distance from the clew to the sheeting block when the jib is fully sheeted in. This will give you a simple, strong, and lightweight set up.
Dan
Edchris177

Rank: Chief

Registered: Nov 26, 2009

Last visit: Apr 10, 2024

Posts: 2524
Posted: Oct 20, 2012 - 11:38 AM

Welcome to The Beach Cats. Most photos that are posted in these threads can be blown to full size by clicking on them.

Quotebut if you luggage tag a line, at its midway point, to a snap shackle, you can then snap the shackle on and off of the clew.

This is exactly what you want. By "luggage tie" he means;
get a 4'-6' length of 3/16"-1/4" line,something half decent, like Spyderline,you don't need pure vectran or other non stretch line.
fold the line in half
pass the fold through the end of a halyard shackle, then pass ends through fold(or make it so a normal captive shackle is contained on the fold.
tie each bitter end to one jib block.
Now all you have to do is put the shackle through the clew, & secure, no knots to deal with. A captive pin shackle is better than a non captive one.
Here is how the N 5.7 is rigged. You would have a captive pin shackle where I have the line attached directly to the clew. The lines dropping out of the photo,(bottom right) attach tot he jib blocks.
I am not using a shackle because this boat sits on a lift at my dock, with roller furling, & the jib never gets unhooked til the season is over.

If you are stepping the mast each time you have to make sure the jib lines are pulled out towards the bow, & outside of the mast before you step it. Otherwise you will have to undo one bitter end from a jib block & move it so the lines go outside of the mast.

As Dan said, the advantage to using a 6' piece of thin line,(3' going to each jib block) is it shortens by 12' (jib is rigged 2:1) the length you need of your jib sheet,making things lighter.
The other line you see tied around the jib is a safety line, to prevent the jib unfurling if the furling line were to come out of the cleat, or break. I sleep better with it there.

Edited by Edchris177 on Oct 20, 2012 - 11:48 AM.

--
Hobie 18 Magnum
Dart 15
Mystere 6.0XL Sold Was a handful solo
Nacra 5.7
Nacra 5.0
Bombardier Invitation (Now officially DEAD)
Various other Dock cluttering WaterCrap
--
HULLFLYER

Rank: Mate

Registered: Aug 06, 2004

Last visit: Feb 24, 2024

Posts: 877
Posted: Oct 21, 2012 - 04:58 AM

What kind of boat do you own? It is very helpful when asking for advice. What is proper on one boat may not work for another boat.
iliketosailDoes anyboby have a good way to connect jib blocks to jib? I was tring to do it with a piece of line. I dont know the knot I should use for easy connect and disconnect. a picture would be great. thanks in advance for your ideas.
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 22, 2012 - 11:42 AM

I have a mystere 6.0 and have been tying the jib blocks every time I rig. just looking for other options the shackle has worked for me as well but is eating up the front of the mast. Thanks for the ideas.
nacra55

Rank: Mate

Registered: Nov 02, 2004

Last visit: Aug 07, 2023

Posts: 626
Posted: Oct 22, 2012 - 01:49 PM

Try a soft shackle

http://l-36.com/soft_shackle_9.php

--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
--
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 22, 2012 - 02:51 PM

thats a big help! thanks
nacra55

Rank: Mate

Registered: Nov 02, 2004

Last visit: Aug 07, 2023

Posts: 626
Posted: Oct 22, 2012 - 04:04 PM

What I did for a buddy was use a stopper knot attached to the jib clew.
http://l-36.com/stopper_loop_alt.php

Then make the first part of the soft shackle but instead of the stopper knot at the end, after the burry, bring the line back out so that you have two lines and make two eye splices to attach the blocks. I don't have a pic for it but it's just a variation of above. The stopper knot end stays with the jib and the other stays with the jib sheets and blocks.
http://l-36.com/soft_shackle_9.php

This is what we use for Spin tack and halyard.
http://l-36.com/halyard_shackle.php

--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
--
yurdle

Rank: Mate

Registered: Aug 22, 2007

Last visit: Jan 07, 2015

Posts: 742
Posted: Oct 22, 2012 - 04:43 PM

QuoteWhat I did for a buddy was use a stopper knot attached to the jib clew.
http://l-36.com/stopper_loop_alt.php

That's pretty neat. I'm going to have to implement a few of those, especially on the lashing blocks.

--
Rob
OKC
Pile of Nacra parts..
--
nacra55

Rank: Mate

Registered: Nov 02, 2004

Last visit: Aug 07, 2023

Posts: 626
Posted: Oct 22, 2012 - 05:18 PM

http://l-36.com/soft_shackle_howto.php

This should have been the second link in my post above.

--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
--
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 22, 2012 - 06:27 PM

Thanks that site is sweet. I think I might even be able to do that. how long did you leave the two ends that splice to the blocks? I was thinking 6" after the burry?Also what type of line and diamater did you use for the jib setup?

Edited by iliketosail on Oct 22, 2012 - 06:39 PM.
nacra55

Rank: Mate

Registered: Nov 02, 2004

Last visit: Aug 07, 2023

Posts: 626
Posted: Oct 22, 2012 - 07:03 PM

Made of 3 mm amsteel, Eyes large enough to luggage tag to blocks and 6 in burry, to do the eyes I used a locking brummel that can be made with only one end of the line free. See the video at the link below.
The video does not show much of a taper, I start my taper about an inch into the burry and pull a strand out about every .5 inch or so leaving about three strands at the end.

http://www.youtube.com/watch?v=rU1b1iYgdgw

To answer your question, the arms of the Y were about 8 inches and the other part about also 8.

Could be made longer depending on the distance between your clew and the blocks.

--
Ron
Nacra F18
Reservoir Sailing Assn.
Brandon, Mississippi
--
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 22, 2012 - 07:10 PM

I just found this

http://youtu.be/jH66tGsWv_Y
pretty good vid
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 22, 2012 - 07:20 PM

THanks for your posts Ron. This should keep me busy For a while!
presto13031

Rank: Mate

Registered: Jan 21, 2003

Last visit: Feb 10, 2015

Posts: 115
Posted: Oct 23, 2012 - 06:41 AM

Here is how I do mine. May try to do a write up on it. http://www.thebeachcats.c…ictures/?g2_itemId=96203

--
Jeff
Houston TX
1986 Hobie 18 Sail# 13031
--
MN3

Rank: Master Chief

Registered: Jun 20, 2006

Last visit: Apr 06, 2024

Posts: 7088
Posted: Oct 23, 2012 - 06:59 AM

iliketosailI have a mystere 6.0 and have been tying the jib blocks every time I rig. just looking for other options the shackle has worked for me as well but is eating up the front of the mast. Thanks for the ideas.

soft shackles are great, but your clew/blocks are going to still hit the mast. adding a pig tail will also (probably) increase the chances of your jib sheet getting fouled on your rotator (as they now can swing around a lot more). but that is rare, and a jib preventer line helps a lot. Images below

I have put some white dacron sail tape on my mast where my blocks beats up the mast

Edited by MN3 on Oct 23, 2012 - 09:22 AM.
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 25, 2012 - 12:21 PM

Thanks andrew ru sailing tomorrow its gonna be windy!!!
iliketosail

Rank: Lubber

Registered: Jun 10, 2010

Last visit: May 02, 2014

Posts: 20
Posted: Oct 25, 2012 - 12:26 PM

That looks nice, you should do a write up, I would be interested.
presto99Here is how I do mine. May try to do a write up on it. http://www.thebeachcats.c…ictures/?g2_itemId=96203