Welcome anonymous guest

Please Support
TheBeachcats.com

Dyneema/Spectra  Bottom

  • Has anyone used this for rigging? It has low elasticity/high strength/low weight.

    --
    Kenneth Purdy
    Hobie 16
    Nacra 5.2 (2)
    Banshee
    First Coast, Florida
    --
  • Yes.
    Guy on the beach next to me for his F18HT. No issue. Had it that way for 2 years now I think.
    Only thing, although the line doesn't strech... the splices will "tighten down" resulting in some slack..
    Of course you have to splice it, but 8 and 12 strand is REALLY easy, simple and fun once you've done 2 or 3.
    I use the stuff all over for soft shackles, and spliced an eye in to my spin halyard (hobie 18)... I also use it for my tramp lacing, since it doesn't strech.
    I have new Ronstan trap handles on order and will be doing my trap lines when the handles arrive.
    Good luck!
  • I don't use it on my standing rigging except for the spin pole lines.

    I do use it as part of the rotater, jib sheet and spin halyard on an F18 and I've laced a P 16 tramp with it. All 1/8 inch Amsteel, bought a spool. Also used it on a P16 to connect the jib blocks and a Nacra 6.0 for the 4 way jib system wire replacement and one piece pig tails for the jib on the P16 an N6.0 . Easy to splice, get a Selma fid or a Brion Toss splicing wand and learn a locking brummel eye splice. Also buy some cheep scissors to cut out strands for the taper. Dyneema is some tough stuff to cut.

    I've thought about using it to replace the trap wires but I still have a spare set of new wires.

    The only place I see H16 guys using it is the Aussie Jib Halyard and they use something bigger than 1/8



    Edited by nacra55 on Aug 31, 2013 - 01:54 PM.

    --
    Ron
    Nacra F18
    Reservoir Sailing Assn.
    Brandon, Mississippi
    --
  • High-modulus polyethylene lines like dyneema/spectra/amsteel/etc are know to have creep (continuous stretch over its life.

    that makes it a less than perfect choice as a side shroud. - It can be done, but you have to occasionally re-tighten your shroud (or watch your mast move forward over time) - plus the chafe factor is always a concern

    vectran has stretch but doesn't have rebound (once stretched .. it is done)

    i have heard most HM lines benefit from a good "tug" before use to reduce stretch and creep of a spliced line

    QuoteOnly thing, although the line doesn't strech... the splices will "tighten down" resulting in some slack..


    Besides my martingales (spin bridals) i can't think of a place i use splices on any standing rigging
  • I was actually thinking about using it for the Hobie 14 Jib Control Line.

    --
    Kenneth Purdy
    Hobie 16
    Nacra 5.2 (2)
    Banshee
    First Coast, Florida
    --
  • if you mean a jib sheet... that is a poor choice of line for that location
    it it too light to effectively "snap" your line out of the jib blocks
    it is (comparatively) expensive line and overkill for that use

    regular xls line is what i use for my jib sheets

    klppurdyI was actually thinking about using it for the Hobie 14 Jib Control Line.
  • No, I did not mean Jib Sheet, on the 14 there is a stainless steel cable that runs underneath the trampoline, and the two jib blocks are attached through grommets on the trampoline.

    --
    Kenneth Purdy
    Hobie 16
    Nacra 5.2 (2)
    Banshee
    First Coast, Florida
    --
  • ohhh. you mean the Jib block support cable.

    yes it will work there

    i strongly suggest you use vecrtran for this application (vs dyneema) for the reasons i mentioned above



    Edited by MN3 on Sep 03, 2013 - 07:18 AM.
  • Great, thanks for the feedback

    --
    Kenneth Purdy
    Hobie 16
    Nacra 5.2 (2)
    Banshee
    First Coast, Florida
    --
  • come to think of it, if this line is under the tramp, i wouldn't splice both sides (or at all)

    i would defiantly try to tie a truckers hitch so i could get some purchase and easily re-tighten the line every few months, or as needed
  • All right,

    I will give it a shot and let you know how it goes. Tramp is being repaired, regrommeted now.

    --
    Kenneth Purdy
    Hobie 16
    Nacra 5.2 (2)
    Banshee
    First Coast, Florida
    --

No HTML tags allowed (except inside [code][/code] tags)

  • Options

This list is based on users active over the last 60 minutes.